The flooring should be beautiful, high quality and neat. Laminate meets these requirements, as it looks modern, has a long service life and is easy to install. Anyone with minimal construction skills can install laminate flooring. All you need is free time and familiarization with installation technology. You need to know what tools you will need to lay laminate flooring so that the work is done quickly and efficiently. We'll talk about this in this article.
Required Supplies
Before we begin installing the coating and answer the question of what tools are needed to lay laminate flooring, let’s consider what you will need from building materials:
- Masking tape to limit the jigsaw.
- Waterproofing film.
- Regular tape for gluing the joints of the substrate.
- A substrate that helps eliminate minor unevenness and insulate the coating.
- Silicone sealant for filling cracks and gaps.
- Mixture for leveling obvious defects on the entire floor.
After purchase Supplies You can prepare a tool for laying laminate flooring.
Required Tools
Most of the necessary tools that you will need are used in everyday life. If something is missing, then you need to purchase it or borrow it from friends.
Electric jigsaw or hacksaw
Not worth buying professional tool if you don't have one. But even the cheapest copies are unreliable, since products with low power can quickly fail.
You will need this tool when laying laminate flooring for cutting and sawing boards. If you use a hacksaw, it should have fine teeth unless you have a gap between the bottom of the door frame and the base flooring.
Important! Choose a jigsaw with a power of at least 500 W, famous brand in the middle price category.
Clamp for laminate or bracket for laying laminate
This is a curved plate with a thickness of at least 5 mm. Along the edges of the plate, bends are made in different directions, but always at an angle of 90 degrees. One edge should be wider than the other.
It is used for tamping the last boards that are laid along the walls. It is necessary for uniform distribution of forces along the entire length. This bracket makes it possible to preserve the edge of the laminate when tapping the panels with a hammer.
The wide edge of the clamp is applied to the end of the laminated board, and the narrow edge is hit with a hammer.
Tamping block
Needed to pad each lamella so that they fit together clearly. When using a lock, you don’t have to worry, since all the lock connections will remain intact. The block can be made of plastic or wood.
Feather drills
Used for neat and precise drilling. With their help, holes are made in the laminate for heating risers or for laying other water pipes.
Important! The holes should be 4-6 mm wider than the passing pipes.
Restrictive wedges for laminate flooring
Necessary for mounting boards to the wall. With their help, you can leave a gap of 8-12 mm, which is necessary for thermal expansion of laminate panels in the off-season. These gaps are closed with skirting boards.
Other tools:
- Replacement blades that fit your electric jigsaw model.
- 5 m tape measure. It is best with a sealed iron tip, which will cling well to the canvas and not move along it.
- Hammer or mallet. Will be needed for precise connection of floor planks and their adjustment. A hammer is used to snap the boards together and tamp them down.
- Stationery knife. Needed for opening laminate packages. You can also use it to cut out the underlay for flooring.
- A simple pencil. For marking laminated flooring.
Important! It is best to use a pencil with a soft lead.
- Square 30 cm. Used for marking corners.
- Goniometer or protractor. Useful if the coating is laid diagonally. You will need a 90 degree angle with which you will mark the lines. The elements will be trimmed based on them.
- Doboynik. Used for final padding of the panel.
- Drill. Both electric and manual are suitable. With its help, holes are made for self-tapping screws during the installation of screeds from plywood sheets.
Important! It happens that there is no tamping block at hand. Never hit the laminate locks with a hammer to avoid damaging them. Use an unnecessary piece of one of the boards, join the locks and very carefully tap the laminate tiles.
Application of new tools
We looked at the most popular tool for laying laminate flooring, but professionals recommend using more advanced tools, which are offered by engineers from the German company Wolfcraft.
Such tools include:
- A machine that is used for cutting PVC plates. This is dust-free and silent cutting of panels without the use of a hacksaw or electric jigsaw. The machine cuts at a right angle. This device very easy to use, you don't need to put in much effort. This result is due to the special structure of the blade in the machine.
- A square that automatically divides an angle. This design makes it possible to effortlessly and quickly measure the angle of walls that are in contact and transfer the result to the laminate panel without problems. The scale starts at 30 degrees.
- Template for marking flooring. With it, you can quickly mark where to cut the final row.
- Contour for applying shapes and bends of the laminate. Needed for marking cutting lines. With its help, it is easy to display the shape, and then apply it to a sheet of laminate, so that later you can cut out, for example, decorative elements or semicircles for pipes. You can also connect template designs from one to another.
Laminate is a practical and beautiful floor covering, characterized by at an affordable price and ease of installation. The interior of the entire living space depends on how carefully the material is laid. To achieve an ideal laminate floor, you need to take care of the necessary tools in advance: prepare a laminate kit for installation, choose what to cut the panels with, prepare additional accessories, decide whether to use power or hand tools.
Each instrument has its own characteristics, technical capabilities and operating techniques which we will discuss in this article. Therefore, after reading to the end, you will understand what tools are needed for laying laminate flooring in order to avoid mistakes and not waste a lot of effort.
Household and professional tools
The floating connection system of laminate flooring allows for installation work the installation of flooring is much simpler and lighter compared to parquet or porcelain stoneware. Before starting work, you should decide what tools you need to lay laminate flooring yourself, prepare them or, if necessary, buy them.
When selecting devices for laying laminate flooring, first of all, the skill and professionalism of the performer, as well as the volume of work to be done, are taken into account. Taking into account such criteria, the classification of instruments can be presented in two categories:
- household tools;
- professional tool.
The difference between the second and the first is the higher intensity of use and improved ergonomics of the design. To withstand increased loads, manufacturers of professional tools use more quality materials, which naturally increases its price.
Advice: If you want to lay a laminate floor with your own hands in an apartment or house with an area of up to 100 square meters, then you shouldn’t overpay for a professional tool. It is enough to buy a household one. And if you are planning to install the floor in a cottage with an area of more than 100 square meters. m., it is better to purchase a professional tool. This will allow you to get the job done faster and you will be less tired.
DIY tools for laying laminate flooring include:
- roulette;
- pencil or marker;
- construction square or metal ruler;
- plastic or wooden block;
- mallet or hammer;
- spacer wedges;
- mounting bracket for laying the last laminate panels;
- any cutting tool on wood or chipboard.
Most of listed items Every owner probably has one in their home. Let's take a closer look at each separately.
Roulette is measuring instrument, which almost everyone has in their home. With its help, it is more convenient than a metal ruler to measure the lamellas before cutting. It is recommended to use a product that has an ergonomic shape and clearly marked markings. This will ensure correct measurements and long service life. To ensure that the tape measure fits well in your hand, use a product with a rubberized body from trusted manufacturers.
Pencil
A pencil is required to mark the sheet. It is most convenient to use construction pencils that have a thick lead and a shell with an oval or rectangular cross-section, which prevents it from rolling off the surface. But if you are not going to install laminate flooring with an area of more than 100 square meters. m., then it is quite possible to use a simple clerical pencil.
When marking laminate flooring, you can use a marker, but it is better not to do this. If you make a mistake and mark in the wrong place or on the wrong side, it will be very difficult to remove traces of the marker.
Square
The construction square is a tool for carpentry work. It is necessary for checking planes and mutual perpendicularity between parts. For household use the tool is presented in the form of two rulers (one thicker than the other), connected at an angle of 90°. In a professional square, you can additionally measure angles and mark radii. When laying laminate flooring, it is very convenient to use a square to mark perpendicular lines for cutting off the excess piece of panel.
Hammer or mallet
Each laminate lamella must be pressed tightly against the previous one so that the coating looks as seamless as possible without gaps and cracks. For these purposes, the board is tapped using a hammer or mallet. It is not always possible to accurately execute a strike and calculate the force. Therefore, in order not to damage the delicate locks of the laminate, an impact block is additionally used. Sometimes it is called a tamper block.
A medium-sized hammer or mallet should be used to ensure good control over the impact force.
Hammer block
An impact block made of wood or plastic is used to tap the lamellas during installation. It is made of impact-resistant plastic or ash, beech, and walnut wood. The block is installed on the opposite side from the panel fastening and a mallet or hammer is used to knock the panel to the already installed ones. Its task is to distribute the load from the impact over a large area and prevent damage. lock element planks.
Spacer wedges
Spacer wedges are designed to install expansion gaps along the edges of laminate flooring. They are pegs of different thicknesses with a slope from one edge to the other. Plastic or hardwood is used for manufacturing. To carry out repairs on small area Alternatively, you can use pieces of laminate or drywall. Professional parts have a special profile for connecting 2 or more elements in different directions.
Mounting bracket
The mounting bracket for laying laminate flooring is metal part for cutting the last laid lamellas towards you (as opposed to the block). It can be sold separately or as a set with a block and wedges. For household use, the bracket has a simple design, but for professionals, it has larger area and felt linings.
Set of tools for laying laminate flooring
Almost everything necessary for installation (tape measure, pencil, hammer, hacksaw, corner) is available to every home craftsman. Manufacturers have combined the missing tools into a set for laying laminate and parquet board, containing:
- spacer wedges made of wood or plastic (usually in a set of 30 to 50 pieces);
- wooden or plastic impact block for tamping panels;
- mounting bracket for laying the last laminate lamellas.
This set of tools for laying laminate flooring can be purchased in stores specializing in the sale of laminate flooring. Prices for devices are affordable. The effectiveness of using auxiliary devices fully justifies the cost of their acquisition.
Experienced flooring installers always have a template in their arsenal to measure curves. It allows for precise adjustment of planks in hard-to-reach places, near protrusions or around utility lines. Using a template, you can easily and quickly draw a cutting line with minimal error. The use of such a tool will help to lay the laminated flooring more efficiently.
Cutting tool
Laying laminate flooring is not complete without adjusting the panels to the required dimensions. It is not possible to install using only solid laminate sheets. Panels of material have to be cut to size when installing each row. For these purposes, you can use any wood cutting tool, since the composition of the laminate is very similar in structure to wood. The most simple option is hand saw or a hacksaw that you have zealous owner in every house.
Advice: before you start cutting, you should stick it on this place masking tape, which will protect against chipping at the cut site. It is recommended to lay the board face up.
If you want to speed up the process and reduce physical costs, it is advisable to use electric tool: jigsaw, grinder or circular saw.
There is an opinion among craftsmen that in order to lay laminate flooring, it is enough to have a minimum set of tools, including a tape measure, a construction pencil, a square, a hammer, a jigsaw or a hacksaw, and the most valuable thing is skill. So minimum set you can get by if you have to lay the laminate in a small area, with clear smooth surfaces without protrusions and partitions.
Desirable accessories for floor repairs include:
- masking tape to protect the decorative layer when sawing off unnecessary parts laminate planks;
- a screwdriver or drill equipped with a crown attachment for cutting holes for pipes and communications;
- a construction or stationery knife for opening packages of material;
- hydro or laser level to check the horizontalness of the base;
- facilities personal protection: gloves, glasses, respirator, etc.
Important! Do not neglect the use of PPE. Gloves will protect the master's hands from accidental scratches, light blows and splinters. When cutting laminate flooring, a lot of sawdust and fine wood dust is formed. Glasses will prevent shavings and sawdust from getting into your eyes, and a respirator will protect your lungs from fine wood dust, which can be saturated with resins containing formaldehyde.
Professional tools for laying laminate, as a rule, have an expanded range components. A professional needs to quickly make decisions in the most unforeseen and non-standard situations, which requires the presence of various non-standard devices and devices for installation: a mounting clamp, various templates, a professional square, a protractor, a metal bracket, multi-level finishers and much more.
A professional tool always has high quality manufacturing. The use of such a tool is designed for long term and intense use. Therefore, it is characterized by the best ergonomic solutions and competent engineering elaboration of individual parts. For the production of such products, materials with high level strength and quality. Therefore, the price of such tools is noticeably higher than that of household ones.
conclusions
When preparing to install a laminate floor with your own hands, think in advance about what you will use to cut the laminate (hacksaw, grinder or jigsaw) and prepare necessary tool for styling (tape measure, pencil, square, hammer and other accessories). The impact block, wedges and mounting bracket can be purchased as a kit for laying laminate flooring in specialized stores.
If you are laying floors in your apartment and do not regularly repair floor coverings, then there is no need to overpay for professional tools. The benefits of purchasing them will only appear with intensive use.
By by and large Laying laminate flooring is not a difficult task. Of course, a specialist in this field will need minimal time to complete this work, but even a person without special training will be able to cope with this task. True, he will need more time for this, but he can save a decent amount on the installation of laminate flooring. Having familiarized yourself with the basic rules and installation technology, you need to figure out what tool you will need to install laminate flooring.
Laminate installation tool
This tool is a must have, it is the most important in this work and is used for accurately cutting the last boards of the row. The cost of such a tool depends on its power, functions and popularity. For an apartment where the amount of work is small, it is enough to purchase a jigsaw with low power - 400-500 W (it costs between 2000-3000 rubles). There is no need to buy a cheaper tool, as it cannot withstand prolonged loads and quickly fails. You also need to get a set of files.
When laying laminate, it is used to tamp the panels in order to eliminate gaps between them. A hammer or wooden mallet weighing 0.5 kg is suitable for this.
No less important tool when laying laminate. Will do metal corner 30-35 centimeters long.
Necessary for marking.
Required for initial stage when measuring the area of the room. Its length is determined by the size of the room. Usually 5m is enough. Craftsmen prefer to use tape measures with a lock.
It is used for padding panels. It is better to use the special plastic block included with the installation kit. His special form allows you to compensate for the impact, preventing damage to the lock of the laminate boards and their surface. The edge of the bar used must be completely smooth so that, when adjacent to the panel, it does not damage it. Therefore, using a regular piece of board instead of a special block is unacceptable.
7. Restrictive or spacer wedges
They are installed between the wall and the lamellas in order to maintain the technological gap. If this is not done, when high humidity indoors, the laminate expands and, resting against the wall, can swell.
It is used to knock down the last panel in the row from the end. On one side it clings to the edge of the lamella, and on the other side it is knocked down with a hammer. It is not recommended to use a mounting bracket instead of a bracket - you can damage the edge of the board, and if the wall is plasterboard, then it will deteriorate.
A metal bracket, spacer wedges and a tamping block - all this makes up the mounting laminate installation kit, which costs about 600 rubles.
The door is usually installed after laying the laminate flooring. But if it has already been installed, then in order to lay the panels under the door frame, it will need to be cut. For this, a hacksaw with fine teeth and a wide blade is used.
11. Miter box (corner cutter)
If the corners of wooden (or MDF) plinths are standard (90º), the cut can be done with only a miter box and a hacksaw. And in cases where the angles of the walls are more or less than 90º, you can’t do without a corner cutter. Plastic skirting boards installed using connecting parts.
Significantly facilitates the work when laying plywood on wood covering, installing interior thresholds and screwing in baseboards. If you don’t have a screwdriver, a reverse screwdriver will do, but if you don’t have one, you can install the baseboard with a simple (Phillips) screwdriver.
It is necessary for opening laminate packages, and also for cutting the backing. You can get by with an ordinary kitchen utensil, but it’s better to have assembly knife.
When laying laminate flooring you will also need the following tools and materials:
- drill for a hammer drill (5x35 and 6x40mm);
- scotch;
- dowel-nails (5x35 and 6x40 mm);
- construction knee pads (to protect the knees).
So, to lay the laminate yourself, you need to have the following tools: tape measure, jigsaw, hammer or mallet, square, construction pencil, hammer drill, hacksaw, miter box (or angle cutter), standard set for laying laminate, a screwdriver or screwdriver. This entire set of tools will cost about 5,000 rubles.
Making laminate flooring is possible even for a person without special skills. All that is required is accuracy, attentiveness, accuracy, and following the manufacturer’s recommendations. By choosing the right tool for laying laminate flooring, you can not only speed up the work, but also guarantee the quality of the flooring, long term coating services, aesthetic appearance floor.
Tool categories
To work with laminate, you will need a set of tools, individual groups of which perform their own functions. Eg:
- devices for installing laminate;
- styling products in accordance with the manufacturer’s recommendations;
- laminate cutting tool;
- marking means;
- additional attachments and accessories.
When considering what tools are needed for laying laminate flooring, one cannot help but note: everyone chooses a specific set, focusing on their work skills and habits.
Marking tools
Marking tools include the usual tape measure or a steel carpenter's meter. It is important to choose a device that not only fits comfortably in your hands, but also does not have any drawbacks that could affect the accuracy of the measurement. Cutting lamellas without errors is the key to quality installation.
In the role marking tool a metal ruler of considerable length may protrude. However, it is worth noting: during the work, you will also have to measure the room. Therefore, it is recommended to use a high-quality tape measure with a length of 5 meters or more.
A construction or carpenter's angle is used to draw cut lines. Do not use a hard pencil. It may leave scratches on the slats. It is convenient to use a water-soluble thin marker or a soft pencil. If you still damaged the laminate, then read how to repair laminate.
Important! Each instrument has its own error. Therefore, all lengths need to be measured with only one device. Changing tape measures is not recommended. Good results are achieved with metal rulers and instruments of the instrumental class, with permissible error 0.5 mm per meter. Using this meter you can evaluate the accuracy of the tape measure.
Aids
To work with lamellas, you will need to fix the part for cutting, as well as make a variety of oblique cuts, pipe contours, and sometimes elements of complex shapes. Therefore, it will not be superfluous following tools for laminate:
- clamps, which can be purchased at any construction tools store;
- feather drills of different sizes;
- durable construction knife.
The set of tools for laying laminate, which are classified as auxiliary, can be supplemented in accordance with the habits of the work performer.
What you need for installation
The main task when laying laminate flooring is not to damage the lamella, especially in the area lock connection. Sharp impacts on a small area should not be allowed. The base of the lamella, an MDF board, is quite easily deformed. In addition, it is necessary to maintain certain gaps between the flooring elements so that they can change size without damaging the coating as the temperature rises or falls. Therefore, when laying, use the following laminate tool:
- small hammer;
- a block of wood, with smooth surfaces, preferably from a fairly soft rock;
- special wedges for forming gaps.
The method of working with the listed devices is understandable to everyone. It is especially worth noting that wedges for forming gaps may be offered by the laminate manufacturer. If such luxury is not available, everything you need can be purchased at hardware stores.
Tip: when working with laminate, it is better to use a mallet (wooden) or a rubber mallet. They are characterized by a distributed impact zone and low inertia. Therefore, even in confined spaces where it is difficult to place a block, such laminate tools can be used without significant risk of damaging the board.
Basic parting tool
After we have considered the tools for laying laminate flooring, markings, and additional accessories, it is worth moving on to the main part. The main operation is precise cutting of the lamellas. And this action can be performed by a whole series of tools.
Jigsaw
An electric jigsaw is almost always included in the tool kit for laying laminate flooring. It is easy to work with, just mark the cutting line and carefully go through it with a saw. In order to decorative surface the lamellas remained intact in the processing area, the board must be cut with the back side up.
Cutting laminate when the board is positioned with the decorative coating facing down is an option for working with a jigsaw, which has a standard straight-grip saw installed. It cuts as it moves up. Beginners who have poor control over the instrument may choose another option. By installing a reverse grip saw into the jigsaw, which cuts as it moves downwards, it is easy to work with lamellas so that you can clearly see the result of your actions.
A circular saw
The circular saw works quickly, efficiently, the tool is convenient and quite light. To cut laminate, special saws with fine teeth of the CleanWood class or ordinary ones for wood are used. In the latter case, it is necessary to strictly check the direction of gripping the material in order to form a clean cut on the side of the decorative coating.
Hacksaw for metal
It is convenient to use a hacksaw to work with narrow lamellas. The disadvantage of this tool is that the saw can damage decorative coating due to some wobbling in inexperienced hands. Therefore, it is recommended to make a cut with a construction knife along the cut line to a depth of 3-4 mm with front side slats.
Bulgarian
A tool that is used to cut steel or angle iron can successfully cut laminate. To do this, you need to use special discs designed for stone, ceramics or concrete.
Construction, stationery knife
Can regular knives. To do this, apply a stop and move the cutting edge of the tool along the marking line several times, each pass deepening by 2-3 mm. You can cut the lamella completely, but it is recommended to place rubber or a wooden block under the processing area. Another option is to leave 1-2 mm of MDF boards and break the part.
Each of the listed tools has its own subtleties of use. For example, a jigsaw is convenient for making recesses for pipes and cutting boards lengthwise along an arbitrary line. A circular saw, hacksaw - designed for transverse cutting of lamellas. Construction knife will require great hand strength, while the grinder will require dexterity and work experience.
The professional segment of tools includes special cutters for laminate flooring. They can be transverse; the board is placed in such a device with support along the long side and, with the force of a handle, is cut off by a guillotine block. Another type of cutter is similar to photographic cutters. It works on the principle of scissor displacement and allows you to cut the board lengthwise and crosswise.
Professional tools are rarely available home handyman, but guarantee cutting accuracy and significantly speed up the laying of the coating. But also those listed simple remedies and devices for careful attention to work will allow you to lay the laminate with high quality, according to all the manufacturer’s recommendations and without visual defects of the surface.
Every professional who lays parquet or laminate flooring has a set of necessary tools.
Read more:
Many people ask the question: what to do for a person who does not lay laminate flooring professionally, and what to do if there are no tools.
The set is necessary to lay laminate or parquet just once.
In this article we'll talk about what tools exist for laying laminate flooring and whether it is possible to complete floor finishing work without them.
Laying features
It is worth noting that laying laminate flooring is a process that is quite labor-intensive. Therefore, every person who plans to do this work himself needs to be patient, acquire certain skills, and also be attentive and careful in relation to every detail, including when laying moisture resistant laminate for Bath.
Of course, you need to have the tools that will help you get the job done perfectly. Today there is no problem to buy any instrument.
Helpful information! In order to use it, you need to have some skills. Therefore, in order to save money, you need to focus on inexpensive tools that are suitable for a novice craftsman at home, including for painting laminate flooring.
It is important to keep in mind that such an inexpensive tool will not last long. You may have to get rid of it after the first work on laying the flooring - laminate or linoleum.
If you want to install laminate flooring professionally, you need to get professional recruitment, which will cost a little more than usual.
What is a laminate kit?
Most kits used to install laminate flooring include several items. This is a block for tamping the laminate slab, wedges, and also a metal bracket. Next, you need to consider what each item is used for.
Wedges
The wedges are designed to leave a gap between the covering and the wall. Wedges also perform the functions of fixing the coating and limiting the sliding of the laminate on the surface. Wedges are needed to secure and provide clearance.
If there are no special wedges that are made of plastic, you can make your own from wood in advance.
Tamping bars
This is a tool, which consists of ordinary blocks of wood, with the help of which laminate slabs are tapped. It is impossible to lay laminate flooring without tamping. Therefore, you need to buy a block that will have a rubber backing. The store sells plastic bars.
Helpful information! You can also line the laminate with a homemade block. However, a lot of time is spent on its production. Finding the required form is not so easy. It is best to buy a ready-made tool in a store.
Metal bracket
Using this tool, the laminate panel is tapped in the last row from the end part.
The bracket is excellent replacement wedges and hammer. If you don’t plan to buy a whole set of tools for laying laminate flooring, then you should look for a similar replacement for these tools at home.
How to install laminate flooring without tools
There is no point in buying a whole set of expensive tools if you need to install laminate in just one room of the apartment. Every man has many other tools in his home that will help him get the job done.
The first tool is an electric jigsaw. It will be needed to cut the required amount of material. For small room a jigsaw will do Not high power. 500 watts is enough. This is a must-have tool that you can’t do without.
Next, you need to choose a light hammer weighing up to 500 grams. It is useful for tapping covering panels. For measuring work you need a tape measure and a pencil. To cut the panel at a strictly 90 degree angle, you will need a corner. The length of its attachment must be at least 35 centimeters.
On door frames Often the material needs to be trimmed. A hacksaw is useful for this. The hacksaw should have a large blade and fine teeth. You definitely need to have a level. A miter box and corner will help when making corner cuts.
Laying the covering
When all the tools are at hand, you can begin laying the coating. Laminate flooring is installed in a floating manner. This means that you only need to connect the plates to each other.
- First you need to form the first row of coverage.
- Next, the second row is attached to it. Laying laminate flooring is carried out according to the same principle as masonry.
- The panels of the second row are shifted by half relative to the first row.
- After this, all other rows are laid to the very end.
- Panels that are laid using glue require compliance with the “tenon and groove” technique.
- Other types of laminate are installed in the same way.
- The laminate that is laid with locks must be joined at an angle.
- You should hear a click when connecting.
Conclusion
It is now clear that without special tools Laying laminate flooring will not work. At the same time, you need to remember that it is not necessary to buy expensive kits that professionals use.
Helpful information! Half of the tools can be made with your own hands, and some can be purchased in the store. Most often, many of the tools are already on the farm.
Experts note that when laying expensive material, it is best to buy a normal tool, so as not to waste money on the purchase later additional material, which can be damaged by improvised tools.
Almost every store that sells laminate flooring also sells several types of installation kits. It is enough to buy at least the most inexpensive set, which can later be used for renovations in other rooms.
The video will help you understand how to properly use this or that tool when laying laminate flooring.
